users should evaluate the suitability of this product for their application. specifcations are subject to change without notice. tyco electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specifcation, without notifcation to buyer. 1 / colors and color code designators shall be in accordance with mil-std-681. however, due to length limitations of the raychem part number, an alternative color code may replace mil-std-681 color code designators. (example: 901/902... may be replaced by axxx.) other codes and suffixes may be added to the part number as necessary, to capture any additional requirements imposed by the purchase order. page 1 of 1 the te logo, tyco electronics, electroloss and raychem are trademarks. raychem wire & cable 501 oakside avenue redwood city, ca 94063-3800 phone: 1-800-227-8816 fax: 1-650-361-6297 dimensions are in inches, and unless otherwise designated are nominal this specification sheet takes precedence over documents referenced herein. referenced documents shall be of the issue in effect on date of invitation for bid. ? 2008-2010 tyco electronics corporation. all rights reserved. specification control drawing 55fb1521 two conductor cable, shielded, jacketed, filter line - electroloss 8-11-10 f this specifcation sheet forms a part of the latest issue of raychem specifcation 55f . jacket - radiation-crosslinked, modified conductive etfe component wires - 55fa0511 cable ratings and additional requirements title date revision shield - tin-coated copper temperature rating: 150c maximum continuous conductor temperature voltage rating: 600 volts (rms) at sea level blocking: 200 3c for 6 hours crosslinking proof test: 300 3c for 7 hours flammability: 3 seconds (maximum); 3 in. (maximum); no faming of facial tissue fluoride extraction: 70 2 c for 168 hours, 250 ppm (maximum) identification and color striping durability: 125 cycles (250 strokes) (minimum), 500 g weight jacket color: black jacket elongation and tensile strength: elongation, 50% (minimum) tensile strength, 3500 lbf/in2 (minimum) note: nominal values are for information only. nominal values are not requirements. jacket flaws: not applicable jacket flexure endurance: 10 cycles, no cracking life cycle: 200 3c for 168 hours low temperature-cold bend: -65 2c for 4 hours shield coverage: 85% (minimum) voltage withstand (dielectric): conductor to conductor and shield, 1500 volts (rms), 60 hz voltage withstand (post environmental): not applicable part number: the "*" in the part numbers above shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wire colors from the jacket color. violet shall be light violet and the designator shall be 7l. example: awg 22, light violet and light violet with a blue stripe component wires, black jacket: 55FB1521-22-7l/7l6-0 cable construction details jacket flexure endurance mandrel diameter (in.) ( 3%) part number 1/ conductor size (awg) shield size (awg) jacket thickness (in.) outside diameter (in.) maximum weight (lbs/1000 ft.) minimum nominal nominal maximum 55FB1521-22-* 22 38 .0060 .008 .134 .145 16.0 .250 55fb1521-20-* 20 38 .0060 .008 .150 .161 20.5 .250 55fb1521-18-* 18 38 .0060 .008 .172 .183 27.8 .250 55fb1521-16-* 16 38 .0060 .008 .188 .201 34.0 .325 55fb1521-14-* 14 38 .0070 .009 .224 .237 46.7 .325 55fb1521-12-* 12 38 .0070 .009 .259 .272 65.2 .500 55fb1521-10-* 10 38 .0070 .009 .307 .322 94.9 .500 this product meets or exceeds all requirements of sae as85485/12 for 22-14 awg, less identifcation. internal wire sizes 22-10 awg meet or exceed all requirements of sae as85485/9, less identifcation. all other awg sizes meet or exceed all requirements of sae as85485, less identifcation.
|
